Managed sourcing from Bangladesh, for export and for buyers at home
Get it sourced

Machinery and handling · Pumps

Slurry pump supplier in Bangladesh

Roptan is a slurry pump supplier in Bangladesh for ash, sand, thickened sludge and other abrasive liquids. Tell us the solids, flow and head: we source horizontal, vertical or submersible slurry pumps from verified sellers, check wet end and seal, and deliver.

  • Verified sellers
  • Checked before it ships
  • Delivered by Roptan

Get slurry pumps sourced

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying slurry pumps in Bangladesh

A slurry pump moves liquid that carries abrasive solids. Its wet end, the casing or liner and the impeller, is designed to be worn and replaced, in rubber or in hard metal such as high chrome iron. Bangladesh buyers range from coal-fired power plants moving ash slurry to dredging and sand contractors and treatment plants moving thickened sludge, duties where an ordinary clean-water pump usually wears out fast.

A slurry pump supplier in Bangladesh should quote the wear parts as carefully as the pump, since liners, impeller and seal largely set the running cost. Roptan takes your slurry data, sources from verified sellers, compares wet end materials, speed and seal arrangement, and checks the spares offer before delivery. The seller installs and commissions the pump.

Kinds of slurry pump

Horizontal slurry pumps

Mounted on a base outside the sump or tank with the drive beside it, so the wet end is easy to reach. Choose one for continuous transfer of sludge, sand or ash.

Vertical suspended pumps

The wet end hangs in the sump below a motor mounted on top. Choose one for pits and sumps where solids collect and the pump must sit in the liquid.

Submersible slurry pumps

Pump and motor work under the slurry, sometimes with an agitator on the shaft to stir settled solids. Choose one for pits, ponds and dredging where a dry pump cannot reach.

Rubber-lined pumps

Elastomer liners and impeller absorb the impact of small particles. Usually chosen where the solids are fine, such as sludge and fine sand.

High chrome pumps

A white iron with chromium added, for hard and coarse solids. Stainless steel resists corrosion better but is softer, so a slurry that is both corrosive and abrasive forces a trade-off.

What a slurry pump supplier in Bangladesh needs from you

Flow and head
Total dynamic head and flow with the real slurry, not water, plus the system curve and the liquid levels in the sump.
Solids
Concentration, particle size distribution, largest particle, shape and specific gravity. Together they set the abrasion class, which the impeller speed must match, and rubber-lined pumps have a recommended maximum solids size.
Behaviour and temperature
How the slurry flows and settles, and its temperature. Concentration is not always steady, so give the range and say what debris can arrive.
Start-up and shutdown
Say how often the pump stops. Settled solids can block the impeller, damage the seal and seize bearings on restart, so plan a flush or resuspension line.
Sump design
Give sump geometry, depth and inflow. Poor sump design, low submergence, settling solids and vortexing cause cavitation and air entrainment.
Duty and access
Continuous or standby duty, a spare pump or wet end, and crane or hoist access for lifting the pump out.

Standards and tests for slurry pumps

ANSI/HI 12.1-12.6
The Hydraulic Institute standard for centrifugal slurry pumps: definitions, application, installation, operation and testing. It sets recommended limits on flow as a percentage of BEP flow and a service class method; ask which service class the seller put your duty in.
EN 809
Common safety requirements for pumps and pump units for liquids, the general safety basis for pumps of European origin.
IEC 60034-30-1:2025
Motor efficiency classes IE1 to IE4. Ask which class the offered motor meets.
ISO 20816-3:2022
Vibration evaluation for industrial machines above 15 kW. A reading at commissioning gives the baseline for trending wear later.
Test certificate
Ask what the seller's performance certificate represents and which liquid the test was run with.

What moves the price of a slurry pump

  • Wet end: rubber lining, high chrome iron or stainless steel, and the wear allowance.
  • Seal: expeller drive, gland packing or a mechanical seal.
  • Size and speed: the impeller speed must suit the abrasion class, and a slower pump for the same duty is usually a larger one.
  • Spares: the kit of liners, impellers and seals held for the site.
  • Configuration: horizontal, vertical suspended or submersible, plus any agitator, strainer or jet ring.

Lead times and delivery

Common sizes with standard wet ends from a seller's stock move faster than a pump built to a duty. A special lining, a large frame, a mechanical seal for hard duty, a spares kit ordered with the pump or a pump imported to order usually add time. Roptan confirms the delivery date and any minimum order in the quote.

Roptan delivers to sites across Bangladesh. Where installation is in scope, the seller sets the pump on its base or in the sump, aligns the drive, connects the slurry lines and any flush line, and commissions the pump: rotation, flow, discharge pressure, motor current and a first vibration reading. Handover includes the curve, the wet end parts list, spares list, warranty and a VAT invoice (Mushak 6.3).

What we check for this order

  • Wet end namedWe check the quote names the wet end material, the liner and impeller part numbers and the wear allowance.
  • Speed against abrasionWe check the offered impeller speed suits your solids, since speed must match the abrasion class.
  • Seal arrangementWe check the shaft seal type, expeller, packing or mechanical, is stated and suits your solids.
  • Spares on the same basisWe compare quotes on liners, impellers and seals as well as the pump, so a low pump price does not hide dear spares.

Questions buyers ask

Should I choose rubber or high chrome?

Rubber-lined wet ends usually suit small particles, and high chrome iron suits hard, coarse solids. Send the concentration, size, shape and weight of your solids, since together they decide how abrasive the slurry is, and the seller proposes the wet end against them.

Why did the pump block after a shutdown?

Solids settled in the casing and line while it stood. Restarting against a settled bed can block the impeller and damage the seal and bearings. Flush the pump and line before stopping, or fit a flush or resuspension line, and follow the seller's start-up procedure.

How often should liners and impellers be changed?

There is no fixed interval: in high-solids service, wear is rarely steady enough for a calendar schedule. Trend vibration, discharge pressure and flow against motor current, change parts when they show wear, and stock spares from your own wear data.

Can a submersible pump handle slurry?

Some can. Dewatering submersibles with open clearances, strainers and sometimes a shaft agitator handle light slurry, usually up to about 15 percent solids, at lower efficiency than clean-water pumps. Heavier slurry calls for a slurry pump with hardened or lined parts.

How soon will I hear back about pumps?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.

Other pump products

Each product type has its own page as it is published; until then its card opens the category form.

All pumps