Managed sourcing from Bangladesh, for export and for buyers at home
Get it sourced

Machinery and handling · Pumps

Centrifugal pump supplier in Bangladesh

Roptan is a centrifugal pump supplier in Bangladesh for water, cooling and process duty. Tell us the flow, head and liquid: we source from verified sellers, check each curve at your duty point and deliver.

  • Verified sellers
  • Checked before it ships
  • Delivered by Roptan

Get centrifugal pumps sourced

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying centrifugal pumps in Bangladesh

A centrifugal pump uses a spinning impeller to throw liquid outwards and turn that speed into pressure. It is the usual choice for clean or lightly dirty liquids: water supply, cooling and chilled water, boiler feed and process lines in textile, food and chemical plants. Most run long hours, so where the pump runs on its curve largely decides its life.

For a centrifugal pump supplier in Bangladesh, quoting a flow and head is easy; matching your system is the real work. Roptan asks for your system curve and liquid, sources from verified sellers, lays their curves over your duty and checks materials, seal and test certificate before delivery. The seller installs and commissions the pump.

Kinds of centrifugal pump

End suction pumps

Liquid enters along the shaft and leaves from the top of the casing. Many follow ISO 2858 dimensions, which makes replacement simple. Choose one for general water and process duty.

Multistage pumps

Two or more impellers in series, each stage adding pressure. Choose one for high head at modest flow, such as boiler feed or lifting water to a high tank.

Split case pumps

The casing splits along the shaft line, so the top half lifts off for inspection and impeller change without disturbing the pipes or the motor. Chosen for large flows, such as cooling water.

Vertical inline pumps

Suction and discharge sit on one line, so the pump mounts in the pipe run itself and takes little floor space. Chosen for plant rooms where floor space is tight.

Magnetic drive pumps

No shaft passes through the casing, so there is no seal to leak; a magnet coupling turns the impeller. Choose one for hazardous, toxic or corrosive liquids such as acids.

What a centrifugal pump supplier in Bangladesh needs from you

Duty point and system curve
State flow in m³/h and total head in metres at the real operating condition, without padded margins, and send the system curve. Ask for the pump curve laid over it.
Distance from BEP
The duty should usually sit within about 70 to 120 percent of the flow at BEP, the point of peak efficiency. Left of it brings recirculation and radial load; right of it, cavitation and overload.
Suction and NPSH
Give the liquid level, suction pipe run and temperature. NPSH available must exceed NPSH required; hot liquid has a higher vapour pressure, which cuts the margin.
Liquid and materials
Name the liquid, solids and chemicals from an analysis. Corrosion and wear both cut performance, so wetted materials should follow the liquid, not the catalogue default.
Motor, supply and speed
State phase at 50 Hz, the starter and any generator backup. Take motor kW from the curve across the whole flow range, and say if demand varies enough for a drive.

Standards and tests for centrifugal pumps

ISO 9906:2012
Hydraulic acceptance tests for rotodynamic pumps, in grades 1, 2 and 3. Ask for the grade on the certificate, so you know which tolerance was applied.
ISO 5199 and ISO 9908
Technical specifications for centrifugal pumps, Class II and Class III. Naming one sets the build quality, so quotes compare on the same basis.
ISO 21049
Shaft sealing systems for centrifugal and rotary pumps. Ask for seal face and elastomer materials by name, with the spares list.
IEC 60034-30-1:2025
Motor efficiency classes IE1 to IE4 for motors run direct on line. A motor fed by a variable speed drive falls under IEC TS 60034-30-2.

What moves the price of a centrifugal pump

  • Size: flow, head and motor kW decide the casing, impeller and motor frame.
  • Wetted materials: cast iron usually costs least; bronze, stainless steel and duplex cost more.
  • Seal: a cartridge or double seal costs more than a single seal, and a magnetic drive more again.
  • Motor and drive: a higher IE class or a variable speed drive raises the price but usually cuts power use.

Lead times and delivery

A pump from a seller's standard range moves faster than one built to a duty. Special materials, a magnetic drive, a large split case pump, a witnessed test or a high-efficiency motor usually add time, more so when the pump is imported to order. Roptan confirms the delivery date and any minimum order in the quote.

Roptan delivers to sites across Bangladesh. Where installation is in scope, the seller aligns pump and motor on the baseplate, connects pipes without strain on the flanges and commissions the pump: rotation, flow and head against the curve, motor current and vibration. Handover includes the curve, test certificate, alignment record, spares list, warranty and a VAT invoice (Mushak 6.3).

What we check for this order

  • Curve at your dutyWe check each offered curve puts your duty inside the preferred region, about 70 to 120 percent of the flow at BEP.
  • NPSH marginWe check NPSH required against NPSH available at your hottest liquid and lowest level, so the pump will not cavitate.
  • Materials and seal namedWe check casing, impeller, shaft and seal materials are named on the quote and suit your liquid analysis.
  • Test certificateWe check the ISO 9906 certificate covers the shipped pump, states its grade and shows flow, head and power at your duty.

Questions buyers ask

Why does my centrifugal pump wear out so fast?

Usually because it runs far from BEP, where recirculation or cavitation shortens seal, bearing and impeller life. In one review of 12 months of data from 464 pumps, 68 percent ran outside the preferred region.

Should I throttle the discharge valve to correct the flow?

It works, but an oversized pump throttled back burns power across the valve. Designers often pad head by 15 to 20 percent, which is how pumps end up oversized. Where demand varies, a variable speed drive is usually the better fix, since pump power falls roughly with the cube of speed.

What does cavitation sound like?

Like gravel rattling in the casing. Vapour bubbles form where suction pressure falls too low and collapse on the impeller, eroding its vanes. Common causes are too little head on the suction side, hot liquid or an elbow fitted right at the inlet flange.

Can a new pump replace my old one without changing the pipework?

Usually, if the old pump is an end suction pump built to ISO 2858. Send the nameplate photo, flange sizes, baseplate dimensions and duty. We source a pump of the same designation and check its curve, shaft height and flanges.

How soon will I hear back about pumps?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.

Other pump products

Each product type has its own page as it is published; until then its card opens the category form.

All pumps