Buying infrared thermometers in Bangladesh
An infrared thermometer reads the temperature of a surface from the radiation it gives off, without touching it. In Bangladesh, maintenance teams in textile mills, power and boiler houses, food plants and workshops use them to find hot spots on motors, bearings and electrical panels, and to check ovens, heaters and moving fabric. This page covers industrial and food surface use only.
Many wrong readings come from the target, not the instrument: a spot larger than the target, or a shiny surface. An infrared thermometer supplier in Bangladesh should match the unit to the job. Tell us the surface, its temperature and the distance. We source from verified sellers, check the datasheet against your use, and deliver.
How to specify an infrared thermometer
- Distance and spot size
- The measured spot grows with distance, and the target should be at least twice the spot size at that distance. Read the spot size for your working distance on the datasheet.
- Laser aiming
- The laser dot only helps you aim. The area measured is not limited to the dot and varies between instruments.
- Emissivity
- Most non-metal surfaces have high emissivity, about 0.9 or above for paint and similar finishes, and most units assume this. Bare, polished metal is lower, so choose adjustable emissivity if you read shiny parts.
- Temperature range and response
- Give the lowest and highest surface temperature and how fast the reading must settle, for example on a moving line.
- Site ambient
- The detector is compensated for the air around it. For hot boiler rooms or outdoor use in Bangladesh's heat and humidity, check the operating ambient range.
- Output
- Handheld display only, or a signal from a fixed sensor to a PLC or logger for continuous monitoring.
Standards, tests and paperwork
- ASTM E2758
- A guide to selecting and using infrared thermometers. Useful for writing your own procedure for spot size, emissivity and distance.
- ASTM E1256
- Test methods for single-waveband radiation thermometers. Ask whether the stated accuracy and response time were determined this way.
- IEC TS 62492-1 and IEC TS 62492-2
- Technical specifications on how the data of industrial radiation thermometers are stated and determined, so you can compare datasheets on the same basis.
- Calibration certificate
- From an accredited laboratory, with the points and the emissivity setting used, so later checks can be compared with it.
Lead times and delivery
Lead times vary. Handheld units are usually catalogue items, while fixed sensors, scanning systems and cameras are more often brought in to order, which adds sea freight and clearance at Chattogram. A calibration certificate adds its own turnaround. Roptan confirms dates and the minimum in the quote.
We deliver anywhere in Bangladesh. Handheld units arrive with batteries, manual and certificate. For fixed-mount sensors and scanners, the seller mounts the head at the right distance and angle, sets emissivity for your surface and checks the signal at your panel. You receive the datasheet, certificate, warranty terms and a VAT invoice (Mushak 6.3).
Questions buyers ask
Why does my infrared thermometer read low on stainless steel?
Polished metal reflects infrared and has low emissivity, so a unit set for most surfaces reads it wrong. Use a model with adjustable emissivity, or put non-reflective tape or paint on the spot, with some loss of accuracy. Note that white paint, though it looks reflective, absorbs infrared well.
How do I find the right emissivity setting?
Measure the same surface with a contact thermometer and adjust the emissivity setting until the infrared reading matches. Keep that setting for later readings of similar surfaces only; a different finish or material needs its own comparison.
Can it read the temperature inside a pipe or a food product?
No. It reads only the surface it sees. For the liquid inside a pipe, the core of a food product or a tight accuracy requirement, use a contact probe such as a Pt100 or thermocouple. The infrared unit stays useful for quick surface checks.
Why does a reading jump near a hot machine?
Near room temperature, radiation reflected from a hotter body can be read as if it came from the target. On a surface with hot and cold areas, the reading can also sit above the true average. Move to cut out reflections and keep the target larger than the spot.
How soon will I hear back about measuring instruments and meters?
Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.
Who do I deal with?
With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.