Photo soon

Photographs will come from the verified sellers who make cable trays and ladders.

Electrical and electronics · Electrical fittings and installation materials

Cable tray and ladder supplier in Bangladesh

Send your tray schedule or drawings to Roptan, your cable tray and ladder supplier in Bangladesh. We source ladder, perforated, basket and channel tray from verified sellers, check the load test against your support span and deliver to site.

Verified sellers
Checked before it ships
Delivered by Roptan

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying cable trays and ladders in Bangladesh

A cable tray system is a rigid support for power, control and communication cables, used in place of open wiring or conduit. Cables are laid in rather than pulled through a pipe, so trays suit buildings where circuits change. Contractors, factories, hospitals and high-rise developers in Bangladesh buy them by the metre, with fittings and supports.

Two trays of the same width can differ in sheet thickness, zinc and tested load. As a cable tray and ladder supplier in Bangladesh, Roptan writes one schedule, sources tray and fittings from one range through verified sellers, checks the test report and coating, and delivers to your site.

Kinds of cable tray and ladder

Ladder tray

Side rails joined by rungs, usually about 100 to 300 mm apart. It carries heavy power cables, with open space between the rungs for air and drainage. Choose it for main runs and risers.

Perforated tray

A base with slots or holes for air, drainage and dust. Choose it for smaller power and control cables that need a continuous base.

Solid-bottom tray

Full cover for the cables but no ventilation, and every cable entry or exit needs a fitting or a cut. Choose it for cables that need full cover.

Wire-mesh basket

A welded wire basket for many small cables, such as telephone and network cable. Choose it for data rooms and offices.

Channel tray

A narrow tray for drops and short branch runs off a main tray where conduit is not wanted; the economical choice for a few cables.

How to specify a cable tray or ladder

Kind, width and side height: State the kind for each run, width and side height in mm, and the cables it carries, so fill and weight per metre can be checked.
Load and support span: Give the cable weight per metre and your support span. Ask for the safe working load at that span and the joint position it was tested with.
Material for the location: Galvanised steel, stainless steel, aluminium or glass-fibre reinforced plastic. Monsoon damp, floods and coastal salt air are hard on outdoor, basement and port-side runs.
Zinc coating: Say pre-galvanised sheet or hot-dip galvanised after fabrication, and ask for the measured zinc thickness and the standard behind it. Field cuts need zinc-rich paint.
Fittings and covers: List elbows at 30, 45 or 90 degrees, tees, crosses and reducers from the tray's own range, and flat or peaked covers for outdoor runs.
Fire walls and floors: Mark where trays cross fire walls and floors, since each crossing needs fire-stopping. Plastic and glass-fibre trays burn unless made fire-retardant.

Standards, tests and paperwork

IEC 61537: The international standard for cable tray and cable ladder systems. Editions differ, so ask for the current edition, which one the test report covers, and the load, span and joint position tested.
US NEMA load method: It starts from the load at which the tray breaks and applies a safety factor, so its figures can read higher than IEC 61537 ones. Compare ratings from one method only.
BS EN ISO 1461: The usual specification for hot-dip galvanising. Its minimum coating depends on the steel thickness, so ask for the zinc measured on the tray offered, not a table figure.
Material certificate and trade papers: A certificate for the metal grade, the seller's trade licence and a VAT invoice (Mushak 6.3).

What moves the price of cable tray and ladder

Material, from galvanised steel to stainless steel, aluminium or glass-fibre reinforced plastic, chosen for each run's location.
Zinc process: pre-galvanised sheet and hot-dip galvanising after fabrication are priced differently.
Size: width, side height and sheet thickness set the weight of metal per metre.
Tested load: a higher safe working load at a longer span needs a stronger section.
Fittings, covers and supports are separate quantities, so a rate per metre of straight tray is not the whole cost.

Lead times and delivery

Time depends on stock of the size and coating, hot-dip galvanising after fabrication, the material, the quantity and whether the tray is imported, since imports wait for port clearance at Chattogram. Roptan confirms the dates and any minimum quantity for each order in the quote.

We deliver anywhere in Bangladesh, bundled and labelled by run or floor, with fittings and supports counted against the schedule. Your electrical contractor or the seller installs, as agreed in the quote. You receive the load test report, coating record, material certificate and a VAT invoice (Mushak 6.3).

What we check for this order

Test report against the quoteWe match the IEC 61537 report to the section quoted: edition, safe working load, support span and joint position, not a similar section.
Coating thicknessWe ask for the measured zinc thickness and its standard, and confirm that zinc-rich paint for field cuts comes with the order.
Sheet thickness and sizeWe measure sheet thickness, width and side height on samples against the quote, since thin steel is hard to spot once installed.
One range for tray and fittingsWe confirm that bends, tees, reducers, covers and couplers come from the same range as the straight tray, so joints fit on site.

Questions buyers ask

Should I use ladder or perforated tray?

Ladder tray usually suits heavy power cables on main runs: open rungs let air and water through and cables are easy to tie down. Perforated tray gives smaller cables a continuous base while its slots still ventilate. Send the cable schedule and we propose a kind for each run.

Why do two quotes give different safe working loads for similar trays?

Usually because the tests differ. Under IEC 61537 the safe working load is set by deflection limits, then an overload step shows the tray does not break; the US NEMA method starts from the breaking load. Limiting the joint to near a support can also change the published load by up to 20 percent.

Is galvanised tray enough for a basement or a coastal site?

It depends on the exposure. Damp basements, flood-prone ground and salt air are harder on fittings than a dry indoor run. For galvanised steel, ask about hot-dip galvanising after fabrication and the measured zinc; for the harshest runs, consider stainless steel, aluminium or glass-fibre reinforced plastic.

Can large power cables be packed tightly on a tray?

Not always. Large power cables may need spacers to avoid overheating, and heavy fireproofing or long fire-stops can trap heat, so the designer may reduce the cable rating. Send the cable schedule with the tray schedule.

How soon will I hear back about electrical fittings and installation materials?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the quantity, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.