Managed sourcing from Bangladesh, for export and for buyers at home
Get it sourced

Machinery and handling · Air compressors

Screw compressor supplier in Bangladesh

Roptan acts as your screw compressor supplier in Bangladesh. Send your air demand, working pressure and running hours: we source oil-injected or oil free screws from verified sellers, compare them on tested power, check them and deliver.

  • Verified sellers
  • Checked before it ships
  • Delivered by Roptan

Get screw compressors sourced

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying screw compressors in Bangladesh

A screw compressor traps air between two meshing helical rotors and squeezes it as they turn. The flow is steady, the machine runs quieter than a piston unit, and it needs no special foundation. The oil-injected, motor-driven screw has become a dominant industrial type. Bangladesh exports few air compressors, so this page is for buyers here.

Screw quotes rarely compare as sent, because each seller states flow and power on its own basis. As your screw compressor supplier in Bangladesh, Roptan asks verified sellers for flow and power at your pressure on the ISO 1217 basis, checks the machine and its papers, and delivers it. The seller installs and commissions it.

Kinds of screw compressor

Oil-injected screw compressors

Oil fills the gap between the rotors, carries away heat and lets one rotor drive the other. Choose it for general plant air, adding filters and a dryer where air meets product.

Dry oil free screw compressors

Timing gears hold the rotors apart, so no oil enters the compression chamber. Choose it only where oil in the air is not acceptable; it costs more to buy and to run.

Fixed speed screw compressors

The motor turns at one speed and the machine loads and unloads to follow demand. Choose it where a steady base load keeps it near full output.

Variable speed screw compressors

A drive matches motor speed to demand. It is most efficient between about 30 and 80 percent speed; at full output, drive losses make it draw more than a fixed speed unit.

Two-stage screw compressors

Two air ends compress the air in series. A US Department of Energy sourcebook rates them generally more efficient than single-stage screws, which suits large machines with long running hours.

What to tell a screw compressor supplier in Bangladesh

Flow at your pressure
Free air delivery in m³/min at the working pressure. A flow figure without a pressure tells you nothing.
Working pressure
What your furthest machine needs plus pipe and filter losses. Near 7 bar, every 0.14 bar added raises energy use by about 1 percent at full flow.
Demand pattern
A week's log of demand. A swinging load favours a variable speed screw, or several smaller machines in sequence, over one large fixed speed unit.
Leaks before sizing
Poorly kept systems can lose 20 to 30 percent of output through leaks; good upkeep brings that under 5 to 10 percent. Repair first, then size.
Dust, lint and humid air
A dirty intake filter cuts capacity and fouled coolers waste power, so plan cleaning in dusty rooms or mills with lint. Order dryer and drains with the screw.
Heat recovery
More than 80 percent of the electricity a compressor takes becomes usable heat. Ask the seller to price recovery for hot water or warm air.

Standards and test papers for screw compressors

ISO 1217
Acceptance tests for flow and power of displacement compressors; Amendment 1 of 2016 added specific energy. Ask for the model's test data on this basis.
ISO 11011
How a whole-system compressed air energy assessment is done and reported. Ask for one before replacing a machine.
EU Machinery Directive 2006/42/EC
Machines from EU sellers carry CE marking under it. Regulation (EU) 2023/1230 replaces it from 20 January 2027, so check which one the declaration names.
Bangladesh Labour Act 2006, section 71
Your factory must take the measures needed so pressure plant never exceeds its safe pressure: a duty on the plant, not an approval of the machine.

What moves the price of a screw compressor

  • Life-cycle electricity: power bills over the years dwarf the purchase price, so judge on lifetime cost.
  • Specific power: indicative full-load figures for single-stage oil-injected screws near 7 bar are roughly 5.6 to 6.7 kW per m³/min.
  • Speed control: a variable speed drive costs more and pays back only where demand varies.
  • Stages and motor size for your flow and pressure.
  • Scope: dryer, filters, receiver, drains, heat recovery and commissioning, or the bare compressor.

Lead times and delivery

We found no reliable published lead time for screw compressors here, so we give no figure. A common oil-injected size a seller already holds usually arrives sooner than a variable speed, two-stage or oil free machine shipped to order, which waits on sea freight and customs. Roptan confirms dates and any minimum in the quote.

We deliver to your plant anywhere in Bangladesh. The seller sets the screw where it gets cool air, connects power, receiver, dryer and drains, and commissions it. At handover, ask for the test data sheet, a commissioning record, the service schedule, the warranty and a VAT invoice (Mushak 6.3).

What we check for this order

  • Tested data sheetWe ask for the maker's tested data sheet for the exact model, with flow and power at your pressure.
  • Separator change pointWe check the seller states when the air/oil separator is changed: it starts at 2 to 3 psid, and manuals usually say about 10.
  • Speed control against loadWe check fixed or variable speed against your demand log, since a variable speed screw near full load gains little.
  • Storage for variable speedWe check a variable speed screw has enough receiver storage, so the drive does not ramp up and down all day.

Questions buyers ask

When is a screw better than a piston compressor?

When air runs for long hours. A screw gives steady flow with less noise and vibration. For very small duties a piston machine often suits better: leakage between small rotors makes small screws less efficient, and piston units work more efficiently at part load.

Is a variable speed screw compressor worth it for my plant?

Only if your demand varies. Efficiency peaks when the drive spends most hours between about 30 and 80 percent speed; near full output, drive losses make it use more power than a fixed speed machine. A week of logged demand settles it.

How much power does a screw compressor use?

It depends on size, stages and pressure. A US sourcebook's indicative figures at 100 psig are 16 to 19 kW per 100 cfm for single-stage oil-injected screws and 15 to 17 for two-stage. Ask for the model's tested figure.

What does a screw compressor need in servicing?

A clean intake filter, oil and oil filter on the maker's schedule, a separator changed at its pressure drop limit, and clean coolers. A clogged separator makes the motor draw more power.

How soon will I hear back about air compressors?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.

Other air compressor products

Each product type has its own page as it is published; until then its card opens the category form.

All air compressors