Managed sourcing from Bangladesh, for export and for buyers at home
Get it sourced

Machinery and handling · Air compressors

Air dryer supplier in Bangladesh

Roptan is your air dryer supplier in Bangladesh for compressed air. Tell us the flow, pressure, inlet temperature and dew point you need: we source refrigerated or desiccant dryers from verified sellers, check the rating at your conditions, and deliver.

  • Verified sellers
  • Checked before it ships
  • Delivered by Roptan

Get air dryers sourced

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying air dryers in Bangladesh

An air dryer takes water vapour out of compressed air after the compressor. Compression heats the air and concentrates its water, so as the air cools in the pipes the water condenses, rusting steel tanks and piping, washing oil from tools and clumping blasting media. In Bangladesh's humid monsoon climate, a lot of water reaches every intake.

As an air dryer supplier in Bangladesh, Roptan asks verified sellers to rate the dryer at your inlet temperature, pressure and flow, not at reference conditions. We check the dew point, pressure drop and drains in the quote, deliver the dryer and its filters, and the seller installs and commissions it.

Kinds of air dryer

Refrigerated air dryers

The most common type: they chill the air and drain off the water, giving a pressure dew point of about 2 to 4 °C. Choose them for general factory air; some cycle on and off at low flow to save energy.

Heatless desiccant dryers

Twin towers of desiccant take turns drying the air and regenerating with purge air. Typically rated at a pressure dew point of minus 40 °C, they suit instrument air, paint lines and pharmaceutical use.

Heated blower desiccant dryers

A heater and blower regenerate the desiccant, so they use no purge air and only a little for cooling. Choose them where compressed air is costly and you accept heater and blower power instead.

Heat-of-compression dryers

Hot air from the compressor discharge regenerates a rotating desiccant drum, so drying runs continuously with no tower switching.

Membrane dryers

A polishing dryer that removes water as air passes through a membrane. Choose it for a small point of use that needs drier air than the main system.

What to tell an air dryer supplier in Bangladesh

Inlet temperature
Give the hottest air temperature leaving your aftercooler in summer. Dryers are normally designed for about 38 °C maximum inlet, and hotter air needs a larger dryer or more cooling.
Flow and pressure
Flow in m³/min at the working pressure, matched to the compressor or compressors that feed the dryer.
Dew point you need
A pressure dew point of about 2 to 4 °C for general air, or minus 40 °C for instruments, paint and air that meets your product.
Filters before and after
A coalescing filter before a desiccant dryer keeps oil off the bed, and a particulate filter after it catches desiccant dust.
Pressure drop
Refrigerated dryers usually add 3 to 5 psid, about 0.2 to 0.35 bar, which the compressor has to make up. Ask for the figure at your flow.
Drains
Automatic drains on the dryer, aftercooler and filters. Drains left open or poorly kept waste compressed air.
Cooling first
Cooling saturated air by about 11 °C removes about half its water, so a working aftercooler takes load off the dryer.

Standards and test papers for air dryers

ISO 7183
Sets the performance data a dryer seller must state and the test methods, for dryers working above 0.5 bar and up to 16 bar gauge.
ISO 8573-1
Purity classes for particles, water and oil. Name the water class your process needs and ask how the dryer and filters reach it.
ISO 8573-3
Test methods for measuring humidity in compressed air. Ask whether the dew point on the commissioning sheet was measured this way.

What moves the price of an air dryer

  • Type and dew point: desiccant dryers reach minus 40 °C and cost more to run than refrigerated ones.
  • Capacity corrected to your inlet temperature, which can push you to a larger size.
  • Energy: refrigeration power and pressure drop, or purge air, or heater and blower power.
  • Filters and drains: prefilters, afterfilters and automatic drains in the package or left out.
  • Elements and media: filter elements replaced as pressure drop rises, and any drying medium a dryer consumes in use.

Lead times and delivery

We found no published lead time for air dryers in Bangladesh, so we give no figure. A common refrigerated size usually comes sooner than a large or heated desiccant dryer, which may be built or shipped to order and then wait on customs. Roptan confirms dates and any minimum in the quote.

We deliver to your plant anywhere in Bangladesh. The seller places the dryer after the aftercooler with its filters, in the layout agreed in the quote, connects power and drains, and commissions it under load. At handover, ask for the rating sheet at your conditions, dew point and pressure drop readings, the service schedule, the warranty and a VAT invoice (Mushak 6.3).

What we check for this order

  • Rating at your inletWe check the quoted capacity is corrected to your summer inlet temperature and pressure, not taken from reference conditions.
  • Dew point under loadWe ask for the outlet pressure dew point measured under load at commissioning, against the figure in the quote.
  • Pressure dropWe check the pressure drop across dryer and filters at your flow, since every extra bit costs compressor power.
  • Drains workingWe check every automatic drain on the dryer and filters discharges at commissioning, so water does not carry downstream.

Questions buyers ask

Refrigerated or desiccant air dryer?

Refrigerated for most factory air: it gives a pressure dew point of about 2 to 4 °C at lower running cost. Desiccant where air feeds instruments, paint or your product: it reaches minus 40 °C. A desiccant dryer works well as a second stage after a refrigerated one.

Why is there still water in my air lines after the dryer?

Often the inlet air is hotter than the dryer's design inlet, or a drain has failed and water carries on downstream. Check the aftercooler outlet temperature against the dryer rating in summer, then check that every automatic drain discharges.

Does a desiccant dryer use compressed air?

Heatless desiccant dryers use part of their dried air as purge to regenerate the bed, so the compressor must make that air too. Ask the maker for the purge figure at your flow. Heated blower types use no purge air and only a little for cooling, but add heater and blower power.

Where should the dryer go in the system?

After the aftercooler, so the air reaching it is cooler and part of the water has already dropped out. In most systems the receiver sits just after the dryer; some plants use one receiver before the dryer and another near intermittent users. Fit a coalescing filter before a desiccant dryer and a particulate filter after it. A second, smaller dryer can polish air near one demanding user.

How soon will I hear back about air compressors?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.

Other air compressor products

Each product type has its own page as it is published; until then its card opens the category form.

All air compressors