Buying compressor parts in Bangladesh
Compressor parts are the consumables and wearing items that keep a running machine at its rated flow and power: intake filters, lubricant and oil filters, air/oil separators, condensate drains, dryer media and line filter elements, and the coolers that must stay clean. Plants, workshops and service contractors across Bangladesh buy them on the maker's schedule, often sooner in hot, dusty or humid rooms.
As a compressor part supplier in Bangladesh, Roptan matches each part to your nameplate and the maker's schedule, asks verified sellers to state plainly whether a part is genuine or equivalent, checks the items against your order, and delivers them to your plant or workshop.
What to send a compressor part supplier in Bangladesh
- Nameplate
- A photo of the compressor, dryer or filter nameplate with model and serial number, so the part matches the machine and its version.
- Running hours
- Hours on the counter and the date of the last service. The maker's schedule sets which parts are due at which hours.
- Site conditions
- Hot, dusty or humid rooms may need shorter intervals than the schedule, so say what the room is like.
- Lubricant specification
- The lubricant type the maker specifies for an oil-flooded screw, with the separator and oil filter set for that model.
- Filter grade and purity
- For line filters, the element grade and the ISO 8573-1 class the filter is meant to reach.
- Readings you have
- Separator and filter pressure drop, oil analysis results or a recent fault, which show what is wearing and how soon.
Standards behind compressor parts
- ISO 12500-1
- Test method for compressed air filters against oil aerosols. Ask whether a replacement filter element's rating was tested this way.
- ISO 8573-1
- Purity classes for particles, water and oil. Filters and separators are chosen to meet a class; measurement methods sit in ISO 8573-2 for oil aerosol and ISO 8573-4 for particles.
- The maker's maintenance schedule
- Not a standard, but the document that governs service intervals, inspection and relief valve testing. Ask for it with every machine and follow it.
Lead times and delivery
We found no published lead time for compressor parts in Bangladesh, so we give no figure. Common filters, separators and lubricant for widely used models are usually quicker to supply than air end parts or items for old, rare or double-acting piston machines, which may need to be shipped. Roptan confirms dates and any minimum in the quote.
We deliver parts to your plant or workshop anywhere in Bangladesh, packed and labelled against your order with the part numbers matched to the nameplate. Where you ask for fitting, we arrange it through the seller. Papers with each delivery: the packing list, any test or rating sheet for filter elements, warranty terms and a VAT invoice (Mushak 6.3).
Questions buyers ask
When should I change the separator on my screw compressor?
When the pressure drop across it reaches the limit in your manual, usually about 10 psid; a new element starts at 2 to 3 psid. Where electricity is costly, changing earlier can pay, because a rising drop makes the motor draw more power for the same air.
Can I use any compressor oil?
No. Use only lubricant that meets the maker's specification for your machine, changed on schedule, and sample it if the maker recommends analysis. Degraded or wrong lubricant can turn corrosive, harming the air end and the efficiency of the whole machine.
Why has my compressor lost capacity?
A dirty intake filter is a common cause: it reduces both capacity and efficiency. Fouled coolers also hurt efficiency, and leaks in the plant waste air before it reaches the user. Check filter pressure drop and clean the coolers first, then look for leaks.
How often should parts be changed in a dusty or humid plant?
Follow the maker's schedule as a minimum. Intervals may need to be shorter in harsher conditions, such as heat, dust or lint. Watch filter and separator pressure drop and oil condition, and send the readings with your next parts request.
How soon will I hear back about air compressors?
Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.
Who do I deal with?
With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.