Buying moulds and dies in Bangladesh
A mould shapes molten plastic or metal into a part; a die cuts, forms or casts it. Plastics makers in Bangladesh buy injection moulds, and metal workshops buy die-casting dies and press tools. In October 2025 the plastics makers' association told the Financial Express that the industry is heavily dependent on imported moulds, mainly from China.
Some local workshops already name moulds among what they make. As your mould and die supplier in Bangladesh, Roptan writes the tool brief with you, places it with a verified toolmaker, checks the steel, the hardness and the trial parts, and hands over the tool you approve. You deal with Roptan only, or post on our requirement board.
How to brief a toolmaker
- Polymer and shrinkage
- Give the plastic, its grade and the shrinkage you expect. Achievable tolerance depends on the part's size and its material.
- Cavities
- One cavity, several of the same part, or a family mould of related parts. More cavities raise output per shot and the mould cost.
- Undercuts and slides
- List every undercut and feature that needs a slide, lifter or movable core. Each adds tooling and cost, so name them at enquiry.
- Steel and hardness
- Name the tool steel to ISO 4957 and the HRC for cavity, core and inserts. P-type steels are the plastic mould steels; H13 is a hot-work grade used for die-casting dies.
- Surface acceptance
- Agree in writing what counts as a reject for sink marks, flow lines and joint lines, with sample parts, since the tolerance standard does not cover them.
- Run and cycle
- Give yearly volume and the alloy for a die. Die-casting die life depends on the molten metal's temperature and the cycle time, and dies usually fail by wear or erosion.
Standards and records for tooling
- ISO 20457:2026
- General tolerances and acceptance conditions for injection, compression, transfer and rotational moulded parts; second edition, August 2026. Ask which tolerance group the toolmaker designs to.
- ISO 4957
- Tool steels. A grade named to it tells you what the cavity is made from, not just a trade name.
- EN 10204 type 3.1
- An inspection document from the steel maker for the block, showing which steel was supplied before machining starts.
- ISO 6508-1
- The Rockwell hardness test method. Ask for HRC readings on cavity, core and inserts after heat treatment.
Lead times and delivery
A tool is not finished when it is machined. Trial shots, measurement and corrections follow until a sample is approved, so time depends on the cavities, slides, steel and hardening, and on how many trial rounds the part needs. Roptan confirms dates for the first trial, the approved sample and any minimum in the quote.
The tool is handed over after you approve the trial parts, with the steel certificate, hardness readings, the trial measurement report and a VAT invoice (Mushak 6.3). If the tool stays with a moulder to run your parts, ownership, upkeep and release are written into the order first.
Buying moulds and dies for export
EPB data for FY2025-26 shows Bangladesh's tooling exports are mostly mould bases (HS 848020), a component that a cavity and core are built into, while finished moulds for plastics or metal are small lines. Roptan quotes importers of bases or moulds FOB Chattogram, with commercial invoice, packing list, certificate of origin and, for EU GSP, a REX statement on origin.
Questions buyers ask
Should my mould be steel or aluminium?
It depends on the run. Aluminium costs substantially less and suits prototypes and short runs, and hard aluminium can reach about 100,000 parts with care. For long runs, hardened steel lasts far longer; many steel moulds are designed for well over a million parts.
How many cavities should my mould have?
Enough to meet your yearly volume at a sensible cycle. More cavities raise output per shot but also the mould cost. A family mould makes related parts together, which suits a set of matching parts ordered in equal numbers.
Does ISO 20457 cover sink marks and flow lines?
No. It sets general tolerances and acceptance conditions for moulded parts, but leaves out surface imperfections such as sink marks, flow structures and joint lines. Agree those in writing with approved sample parts before the tool is accepted.
How long will a die-casting die last?
It depends on the alloy, the molten metal's temperature and the cycle time, and dies usually wear out by erosion. Ask the toolmaker to state the expected life in shots for your alloy in the quote.
How soon will I hear back about light engineering and machinery parts?
Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the quantity, where it is needed and by when.
Who do I deal with?
With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.