Buying machinery spare parts in Bangladesh
A machinery spare part is the piece built to wear so the machine does not: a bush, a sprocket, a pin or a shaft. Mills in Bangladesh order them for textile, jute, steel, sugar and dyeing machinery. A 2025 conference paper traces local parts workshops to the years after 1980, around Dholaikhal, Jinjira, Mirpur and Syedpur, later Jashore and Bogura.
A spare has to suit a machine already running. As your machinery spare part supplier in Bangladesh, Roptan turns the worn sample into a written specification, places it with a verified workshop, checks the first piece and delivers. You deal with Roptan only, or post the need on our requirement board.
How to specify a spare part copied from a sample
- Chain number and rows
- Send the chain number or a length of old chain, not a tooth count. The sprocket must match pitch and number of strands.
- Fits as tolerance classes
- Write each bore and seat as an ISO 286-1 class, such as H7 on the bush bore with h6 on the shaft, a common close fit.
- Run-out
- Shafts, rollers and couplings that must run true need run-out limits to ISO 1101 on each bearing seat.
- Steel to its ISO 683 part
- Part 1 covers non-alloy steels for quenching and tempering, Part 3 case-hardening steels, Part 17 bearing steels.
- Hardening method and depth
- Induction hardening typically suits about 0.40 to 0.45 per cent carbon equivalent and gives about 37 to 58 HRC. Carburising suits low-carbon steel, with a case typically around 0.5 mm.
- Heat treatment on the drawing
- Show hardness, case depth and test position as ISO 15787 sets out.
Standards and papers for spare parts
- ISO 606
- Short-pitch precision roller and bush chains and their sprockets. Ask for both made to it, so pitch and tooth form are defined, not copied by eye.
- EN 10204 type 3.1 or 3.2
- Inspection documents for bars, forgings and castings. A 3.1 comes from the maker's own inspection; a 3.2 adds an inspector for the buyer or an official body.
- ISO 6508-1 and ISO 6507-1
- Rockwell and Vickers hardness test methods. State the scale and where the reading is taken: a reading on the core says little about the wearing face.
- ISO 2859-1:2026
- Third edition, January 2026, of the attribute sampling scheme for accepting a batch. Older papers may still cite the 1999 edition.
Lead times and delivery
Time depends on the steps the part needs. A bush or pin turned from bar stock is quickest. A casting, hardening, grinding or a material test adds time, and a set takes as long as its slowest piece. Roptan confirms the dates and any minimum in your quote.
We deliver to the mill or factory anywhere in Bangladesh. Each part is labelled with the machine and position it fits, sets are packed together, and the inspection record goes with them, with material certificates where ordered. A VAT invoice (Mushak 6.3) comes with the delivery.
Buying machinery spare parts for export
EPB data for FY2025-26 shows Bangladesh exporting machinery parts under HS 8487, almost all in 848790, a residual line for parts of many kinds of machine, so the drawing defines the part, not the code. Roptan quotes importers FOB Chattogram with commercial invoice, packing list, certificate of origin and, for EU GSP, a REX statement on origin.
Questions buyers ask
Should I replace the chain and sprockets together?
Usually yes. A roller chain lengthens as it wears and the sprockets wear with it, so a new chain on old sprockets soon fails. Replace all three together, and send the chain number so the new set matches pitch and strands.
What should I send if I have no drawing?
The worn part and the part it runs against, the machine type and model, and where the part sits. Mark the faces that wear. Steel and hardness do not show from outside, so we have them tested before copying.
What is the difference between a 3.1 and a 3.2 certificate?
Both are EN 10204 inspection documents. A 3.1 is issued by the maker and validated by its own inspector, independent of production. A 3.2 adds an inspector acting for the buyer or an official body.
Bronze or plastic bushes?
Bronze on a hardened steel shaft is the usual pair. Plastic bushes run without lubrication and sintered bushes carry their own oil, so either suits a point that is hard to reach.
How soon will I hear back about light engineering and machinery parts?
Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the quantity, where it is needed and by when.
Who do I deal with?
With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.