Managed sourcing from Bangladesh, for export and for buyers at home
Get it sourced

Machinery and handling · Valves

Gate valve supplier in Bangladesh

Roptan acts as your gate valve supplier in Bangladesh. Send size, rating, body material, stem type and service: we source from verified sellers, check certificates and test records, and deliver to site.

  • Verified sellers
  • Checked before it ships
  • Delivered by Roptan

Get gate valves sourced

Prefer to deal with suppliers yourself? Post it on the requirement board

Buying gate valves in Bangladesh

A gate valve opens and closes a line by lifting a gate clear of the bore or lowering it across the flow. It is an on-off isolation valve, usually from about 2 inch upwards. Buyers in Bangladesh fit gate valves on water mains, hydrant connections, heating loops and sewers, and in steel on steam, oil and process lines.

The risks are a valve built to the wrong standard, rated too low at your working temperature or cast in a brass that fails in water. A gate valve supplier in Bangladesh should catch these early: Roptan sources from verified sellers, names the design standard on the quote and checks each lot against its certificate.

Kinds of gate valve

Rising stem wedge gate valves

The stem rises with the gate, so you can see whether the valve is open. The gate is most often a wedge pressed onto the seat. Choose it where there is headroom.

Non-rising stem gate valves

The stem turns inside the gate and does not move up. Choose it for valve chambers, pits and tight plant rooms with little vertical space.

Knife gate valves

A thin gate with a knife-like lower edge that cuts through thick media. Choose it for sludge, slurry and pulp lines, not for clean water or steam.

Small steel gate valves

Compact steel valves of DN 100 and smaller, with flanged, threaded, welding or extended-body ends. Choose them for small branch lines in steam, oil and gas plant.

Cast iron and bronze gate valves

Cast or ductile iron bodies for water, fire and building services, and copper alloy bodies for building water. State the copper alloy grade on the order.

How to brief a gate valve supplier in Bangladesh

Duty
Say the valve will only isolate. To regulate flow, order a globe or control valve: a part-open gate vibrates and its open area changes unevenly.
Size and rating
DN or NPS, PN or Class, and the working temperature: a steel valve's allowed pressure comes from the ASME B16.34 table at that temperature.
Stem and headroom
Rising or non-rising stem, and the clear height above the valve for a rising stem's full stroke.
Body and trim
Cast or ductile iron, cast carbon steel, forged or alloy steel, stainless steel or gunmetal. For copper alloy on building water, ask for DZR brass or gunmetal.
Ends and length
Flange drilling to EN 1092-1 (PN) or EN 1759-1 (Class), and face-to-face to EN 558 or ISO 5752, so a replacement fits the old gap.
Design standard
API 600 or ISO 10434 for bolted bonnet steel valves, API 602 or ISO 15761 for small steel valves, EN 1171 for cast iron.
Operation
Handwheel, gearbox or electric actuator; for an actuator, three phase power, the control signal and the closing time.

Gate valve standards and test records

API 600 and ISO 10434:2020
Bolted bonnet steel gate valves for oil, gas and process plant. Ask which API 600 edition applies.
API 602 and ISO 15761:2020
Steel gate valves of DN 100 and smaller. ISO 15761 also covers small globe and check valves, so the quote should say gate.
EN 1171:2015 and EN 12288:2010
European product standards for cast iron gate valves and copper alloy gate valves.
EN 1074-1 and EN 1074-2
Fitness-for-purpose requirements and tests for drinking-water valves; Part 2 covers isolating valves.
API 598:2023, ISO 5208:2015 or EN 12266-1:2012
The pressure test behind the record. API 598 gives a gate valve shell and seat tests, plus a backseat test where it has a backseat.

What moves the price of a gate valve

  • Body material: cast and ductile iron valves for water usually sit at the low end; stainless, forged and alloy steels cost more.
  • Pressure and temperature: pressure seal bonnets and heavier walls for high-pressure steam usually cost more.
  • Design standard: a valve built and documented to API 600 or ISO 10434 usually costs more than a general waterworks valve.
  • Operator: a gearbox or an electric actuator adds to the price of the valve.
  • Documents and inspection: 3.1 certificates, PMI and tests witnessed at the maker add cost per lot.

Lead times and delivery

Iron gate valves in common sizes are often in importers' stock and arrive sooner than steel valves built to API 600 or ISO 10434. Large sizes, high classes, special alloys, actuators and witnessed tests usually add time, more so when valves are imported to order. Roptan confirms the date and any minimum order in the quote.

Roptan delivers to sites across Bangladesh with flange faces covered and each valve tagged to its line on your schedule. Your piping contractor usually fits them. Handover includes test records per lot, material certificates, datasheets, warranty and a VAT invoice (Mushak 6.3).

What we check for this order

  • Markings against the certificateWe match body markings for size, rating, material and heat number to the EN 10204 type 3.1 certificate for that lot.
  • Test record for the lotWe check the record names its standard, the leakage rate accepted and the serial or lot numbers shipped.
  • Material on a sampleFor stainless and alloy valves we ask for PMI on a sample, by OES when an L grade must be confirmed.
  • Fit to your lineWe check stem type, flange drilling and face-to-face against your schedule, so each valve fits its gap.

Questions buyers ask

Should I order a rising or a non-rising stem?

Choose a rising stem where there is headroom, since you see at once whether the valve is open. Choose a non-rising stem for underground chambers, pits and tight plant rooms. Measure the clear height above the valve before you order.

Why do some brass gate valves fail in building water lines?

In stagnant or slow-moving water, ordinary brass can lose its zinc and leave a weak copper body. Dezincification-resistant (DZR) brass or gunmetal resists this, so state the alloy on the order and ask for it on the certificate.

Is a knife gate valve a normal gate valve?

No. Its thin gate has a sharp lower edge that cuts through solids, so it suits sludge, slurry and pulp, not clean water mains or steam. Tell us the medium and its solids so the seller offers the right kind.

Which HS line is a gate valve imported under?

Heading 8481, in the group for other valves. Tariffs that extend the code give separate lines for cast iron and steel gate valves. Your customs broker confirms the full line.

How soon will I hear back about valves?

Within 48 hours of a complete requirement, with a price and a delivery date. A requirement is complete when it has the model or specification, where it is needed and by when.

Who do I deal with?

With Roptan, when Roptan manages the order: we buy from the verified seller and deliver to you. With the supplier directly, when you post on the requirement board and choose a quote yourself.

Other valve products

Each product type has its own page as it is published; until then its card opens the category form.

All valves